Independent lamp guides for Australian homes.

LampScout / Lighting advice

Lampshade size guide: 7 practical checks before you buy

Choose a shade that suits your lamp's dimensions and fitting, allows the bulb clearance required by its instructions, and works in the space where it will stand. The proportions in this lampshade size guide are starting points, not a universal formula. Measure the lamp, check the attachment and compare the shade in its intended position before ordering.

Check your tabletop space
Lampshade size guide scene with a table lamp, two spare linen shades and a measuring tape on a walnut console
Generic AI-generated styling illustration. It does not establish dimensions or fitting compatibility.
Measurements / fitting checks / tabletop calculator
1Take the measurements

Lampshade size guide: measure the lamp and shade separately

Start with the base height, its widest point and the fitting. For a replacement shade, record the top width, bottom width and height as separate measurements. A single number such as "30 cm" is incomplete unless the seller tells you which dimension it describes.

Keep the measuring points consistent. "Lamp height" might mean the ceramic body, the height to the socket, or the finished lamp including its shade. Those are different measurements. A sizing rule based on one cannot be applied reliably to another.

When measuring an existing tapered shade, distinguish vertical height from slant height. Vertical height goes straight from the lower rim's level to the upper rim's level. Slant height follows the side. Florabelle's measuring guide uses slant height in its shade measurements, so read the listing's convention before comparing numbers.

Four dimensions to identify on a tapered shadeTop width, bottom width, vertical height and slant height are different measurements. The diagram is not to scale and does not specify a fitting or bulb clearance.Top widthBottom widthVerticalheightSlantheight
Measurement definitions only. Ask the seller whether the quoted height is vertical or along the side.

Write a short measurement note

A useful note might say: "Base: 38 cm to the fitting, 16 cm at the widest point. Existing shade: 20 cm top, 30 cm bottom, 22 cm vertical height. Ring fitting, with the ring recessed above the lower rim." These are illustrative dimensions, not a recommended combination.

Add a photograph of the current attachment. An image of the whole lamp is useful for styling, while a close-up of the ring or harp answers the fitting question. Keep those records together so you can ask the supplier about one clearly described lamp.

If the shade is missing, use the lamp's model documentation or ask its maker for compatible shade specifications. A missing shade gives you fewer measurements to copy, but it does not remove the fitting and bulb-clearance requirements.

2Compare the proportions

Why lampshade sizing rules do not always agree

You will find advice to make a shade about twice the width of the base, as well as advice to match shade width to base height. Both are styling shortcuts. Their results can differ substantially on a narrow, tall base or a short, broad lamp.

Pip & Haze suggests doubling the widest part of the base for shade width and using roughly two-thirds of the base height for shade height. Pooky instead suggests a shade's lower diameter close to the base height, with adjustments for tall, thin and short, wide bases.

Use a proportion rule to choose candidates to compare. The fitting, bulb instructions, available room and your preferred appearance still decide which candidate works.

For an imagined base 40 cm tall and 15 cm wide, doubling the width suggests a 30 cm shade. Matching width to height suggests 40 cm. That 10 cm difference is enough to matter on a compact bedside table. Averaging the results would not tell you whether either shade attaches correctly or sits comfortably beside the bed.

Start by comparing the two outlines in the room. Record what each solves and what it introduces. A wider shade may look balanced from the doorway but take up space beside the pillow. A narrower one may fit the table well yet leave the holder visible from a seated position.

Manufacturer examples are more specific than a formula

William Yeoward's lamp and shade specification sheet gives recommendations for named bases. The examples below show that different bases can have different shade relationships. They are maker recommendations for those models, not sizes to copy onto unrelated lamps.

Selected William Yeoward specifications
Named baseHeight to middle of fittingMaker's shade suggestion
Alfie Junior43 cm40 cm drum
Elden41 cm45 cm drum or 47 cm oval
Nerys35 cm40 cm drum
Tom46 cm30 cm rounded rectangular

Notice the measurement definition in that sheet: height to the middle of the fitting. It is not the finished lamp height. For the oval and rectangular options, also obtain depth and orientation before judging how much table space they occupy.

3Confirm the attachment

Lampshade fitting types matter as much as width

A replacement lampshade can be the right visual size and still have the wrong attachment. Identify whether it fits around the holder, sits on a harp and finial, clips to a permitted bulb shape, or is designed for suspension. Then confirm the actual dimensions and mounting position for that system.

The Temple & Webster fitting guide distinguishes socket-ring, recessed-ring, finial and pendant arrangements. It also explains shade recess: the distance between the lower rim and the attachment ring. Changing that distance can change where the shade sits without changing its external height.

Some Australian listings mention B22 or E27 compatibility and include a reducer ring. That is product-specific information. Confirm the selected shade's included hardware and the lamp holder it is meant to fit. Do not treat a bulb's cap name as a complete specification for the shade attachment.

What if the ring measurements seem inconsistent?

Ask the supplier which diameter is being quoted. Guides and listings can describe the holder, the ring opening or the adapter using different measurements. Sending the measured opening and a close-up photograph is more useful than assuming that every item sold as a "standard shade" has the same dimensions.

3Chooks' Australian shade guide also advises checking the washer fitting against the holder. Its measurements are a buying reference for its guidance, not permission to force an almost-fitting attachment.

If a shade sits loose, tilts or needs improvised packing, stop and confirm the intended hardware. Altering the ring or lamp holder to make it fit can create a different installation from the one the manufacturer permits.

Table shades and pendant shades are not automatically interchangeable

Confirm whether the selected shade is intended to sit on a base or hang from above. A similar outside shape does not establish the correct mounting direction. Pooky specifically distinguishes its base-mounted shades from pendant shades in its buying guide.

For a ceiling installation or any wiring change, use a licensed electrician. This guide concerns choosing a compatible shade; it does not provide installation or rewiring instructions.

4Choose the outline

Drum vs empire lampshade: compare the space they occupy

Once you have a compatible attachment, compare shape using the outside dimensions. A drum has similar top and bottom widths. An empire shade narrows towards the top. An oval shade has a width and depth that both need checking.

Drum

Check both the lower footprint and the space near the top.

Empire

Record the top and bottom widths separately.

Oval

Check depth and how the shade will face on the lamp.

For a narrow console, a shape with less depth may be worth comparing. For a bedside lamp beside a broad headboard, the upper outline can matter as well as the bottom rim. Measure the relevant nearby objects instead of choosing from a front-facing photograph alone.

Try viewing the lamp from your ordinary seated position. Can you see the bulb or holder beneath the rim? Does the shade block the switch or make it awkward to reach? A shade can look tidy at standing height and feel inconvenient when you are lying in bed.

Material changes the result after the shape is chosen

3Chooks explains that pale or fine fabric can let the shade glow, while darker or thicker material can direct more light through its open ends. Compare the material and lining as well as the colour shown in a photograph.

For reading, look at the page in the intended position. A decorative shade that looks attractive in the room may not put light where the book needs it. Keep the lamp's purpose in view when comparing finishes, without assuming a dark shade or a particular outline gives a measured level of illumination.

Check 5 / Try the footprint

Will a round lampshade fit over your tabletop?

Enter the table width and depth, then try a shade diameter. This plan-view calculator assumes the lamp is centred and the shade is circular. The shaded circle is the shade's projected footprint, not the lamp base.

Each side margin = (table width − shade diameter) / 2. Front/back margin = (table depth − shade diameter) / 2. Positive numbers mean the centred outline stays inside the table edges; negative numbers mean overhang. These are geometry calculations, not safety-clearance requirements.

Centred tabletop margins

5 cmat each side
2.5 cmat front and back

The centred shade outline stays within the tabletop. Check wall space, access and the lamp's stability separately.

Top view of shade and tableA 30 centimetre circular shade is centred over a rectangular table 40 centimetres wide and 35 centimetres deep. Side margins are 5 centimetres and front and back margins are 2.5 centimetres.Table width: 40 cmShade diameter: 30 cm / Table depth: 35 cm
Calculated to a shared scale from the entered centimetre dimensions. The lamp is assumed to sit at the centre.

A lampshade for a bedside lamp needs room around it

The outline in the calculator is a useful first check, but the lamp may not sit in the middle of the table. A wall, headboard, curtain or power point can change its position. Measure from the intended lamp centre to the nearby boundaries before deciding where the shade will sit.

Hello Boho's size guide recommends measuring the table and considering shade overhang, particularly beside a bed. Treat this as practical placement advice. A centred outline that fits inside a rectangle does not establish that the lamp is stable or clear of curtains.

For an illustrative 40 × 35 cm tabletop and a 30 cm round shade, the centred projection leaves 5 cm at either side and 2.5 cm at the front and back. Moving the lamp towards the rear reduces the rear margin by the same distance and increases the front margin. The tool intentionally keeps the lamp centred so its assumptions stay clear.

Leave room for the things you actually use: a glass, a book, a phone and the route your hand takes to the switch. Check the lamp base's footprint separately. The shade occupies space above the table, while the base occupies the surface; those can create different constraints.

Try an outline before buying

You can compare a proposed shade width by measuring that span in the intended position. For a more detailed comparison, mark its footprint on the empty tabletop while the lamp is removed. Do not put paper or a makeshift template over an operating bulb.

If the wider candidate makes the bedside table feel crowded, compare a different shape or a smaller approved option. A narrow-depth oval might merit a closer look, but confirm its orientation and fitting first. The round-shade calculator does not model oval or rectangular shades.

6Check the bulb and heat limits

Shade proportions do not establish bulb clearance

The lamp, shade and bulb instructions determine the permitted bulb type, actual input power and any required clearance. Do not infer a safe bulb-to-shade gap from a styling ratio or use a generic number taken from an unrelated shade.

The US Department of Energy's bulb-selection guidance explains that enclosed fittings can trap heat and affect some LEDs' performance and life. It recommends checking whether the bulb is suitable for enclosed use. If a replacement changes the enclosure around the bulb, confirm the applicable instructions for that arrangement.

An LED's lower power consumption does not settle every compatibility question. The government's Energy Rating advice also distinguishes actual power, light output and dimmer compatibility. Keep those bulb choices separate from the shade's decorative dimensions.

Use the instructions for clearance and bulb limitsA lamp, a bulb and a shade each have relevant instructions. No numeric clearance or wattage is inferred from the decorative proportions.LampPermitted bulb and shadeBulbPower and enclosure ratingShadeAttachment and clearanceConfirm the permitted combination.
Compatibility diagram, not a wiring plan or a temperature model.

Switch off and unplug the lamp before changing its shade, and let the bulb cool. Follow the product instructions for removing and refitting the hardware. Keep fabric, paper and other materials away from areas where the instructions prohibit them.

If the holder, lead or base is damaged, do not keep trying shade combinations. Queensland's Electrical Safety Office advises against using suspected faulty equipment. A new shade cannot repair a damaged lamp.

7Confirm the listing

Before ordering a replacement lampshade

Compare the listing with your measurement note. Find the external dimensions, height convention, fitting type, ring size, recess and included adapter information. If a detail is missing, ask the seller before ordering instead of interpreting a photograph as a specification.

For example, a listing might say "30 cm drum" while the detail sheet gives a separate height and attachment position. Another 30 cm drum can sit differently on the same lamp because its ring is recessed by a different amount. Equal outside widths do not guarantee equal finished lamp heights.

Madam Lampshade's guide provides product-specific size and adapter information alongside styling advice. That illustrates the distinction between a broad proportion suggestion and the hardware supplied with a particular shade. Obtain both kinds of information for the item you select.

Once you know the required dimensions and fitting, these Amazon AU searches can help you compare replacement shades. They open search results rather than a tested shortlist. Confirm the selected shade's specifications, supplied hardware and compatibility with your lamp.

As an Amazon Associate, LampScout earns from qualifying purchases. Search results are not a confirmation of fit, availability or product quality.

A supplier enquiry that can get a useful answer

Send the lamp model, base dimensions, fitting photo and the proposed shade model. Ask whether the attachment is compatible, where the shade will sit and which bulb limits apply. Include the space available near a wall or bed if it affects the choice.

After fitting an approved shade, inspect it from your normal viewing positions. Check that it sits level, the switch remains accessible and it does not contact nearby furnishings. Keep the model and dimensions in your records for the next replacement.

What size lampshade do I need? Common questions

How wide should a lampshade be compared with the base?

Start with the maker's advice for your lamp. Doubling the base width or matching shade width to base height are styling shortcuts used by some suppliers. Compare their results in your space and confirm fitting and bulb requirements separately.

How do I measure a lampshade for replacement?

Record top width, bottom width, height and attachment details. For tapered shades, confirm whether height means vertical height or slant height. For oval or rectangular shades, record depth as well as width.

Does a lampshade size guide apply to every lamp?

No. General proportions can help you shortlist sizes, but individual lamp geometry, mounting hardware and product instructions differ. Use a guide as a starting point and confirm the exact combination.

Should a bedside shade be narrower than the table?

Compare both table width and depth with the shade's footprint. A centred circular shade may fit within the tabletop while still being awkward near a wall or pillow. Check the actual lamp position and access to everyday items.

Can I use an oval shade to save space?

It may be worth comparing when depth is limited. Check the oval's full width, depth, orientation and mounting arrangement. Its widest dimension alone does not establish the space it occupies.

Will an E27 shade fit a B22 lamp?

Only if the specific shade, holder and intended hardware are compatible. Some shades include an adapter, but that is not universal. Confirm the ring dimensions and supplied adapter with the seller.

How much space should there be between a bulb and shade?

Use the clearance stated in the relevant lamp, shade and bulb instructions. This article does not give a universal gap because the permitted arrangement depends on the products and bulb type.

Can I hang a table lampshade from a pendant fitting?

Only when that shade is designed and approved for the mounting arrangement. Base-mounted and pendant frames can put the attachment in different positions. Ask the maker and use an electrician for installation where required.

Why does my new shade sit lower than the old one?

Check the recess and attachment position. Two shades with similar external dimensions can sit at different heights because their internal mounting hardware differs. Compare the old and new fitting details with the lamp unplugged.

Sources and measurement notes

  1. Florabelle Living: lampshade selection and measuring. Measurement conventions and shade geometry.
  2. Pip & Haze: shade size guidance. Width and height proportions, treated as styling advice.
  3. Pooky: lampshade buying guide. Alternative proportions and base versus pendant mounting.
  4. William Yeoward: lamp heights and shade guide. The four named-model examples in the table.
  5. Temple & Webster: fitting guide. Attachment types and recess definitions.
  6. 3Chooks: shade sizing guide. Washer checks and qualitative fabric considerations.
  7. Hello Boho: lampshade size guide. Considering tabletop space.
  8. Madam Lampshade: size guide. Product-specific sizing and adapter information.
  9. US Department of Energy: bulb selection and Australian Energy Rating: choosing a lamp. Enclosure, bulb and control checks.
  10. Queensland Electrical Safety Office: equipment condition. Avoiding suspected faulty equipment.

Styling ratios are supplier suggestions, not standards or safety limits. The calculator uses ordinary geometry and your entered dimensions; it assumes a centred circular shade over a rectangular tabletop. No lamps or shades were physically tested for this blog. No current product prices or Amazon availability are quoted.