How much does a desk lamp cost to run?
Desk lamp running costs depend on watts, hours of use and your electricity rate. An 8 W lamp used for four hours a day at an assumed 40c/kWh costs about $4.67 a year, excluding standby power. Use the calculator below to estimate your own lamp in Australian dollars.
Calculated example: one 8 W lamp, four hours daily, 40c/kWh. This rate is illustrative, not an Australian average or a quoted electricity plan.
Desk lamp running costs: the short answer
A lamp drawing 5 to 12 W for four hours each evening would cost roughly $2.92 to $7.01 a year at the example rate of 40c/kWh. Those are calculated scenarios, not a measured range for every LED desk lamp. A larger lamp, a charging feature or a different power setting can change the result.
The useful starting point is the lamp you actually own. Look for its operating power in watts, decide how long it runs, then use the usage rate from your electricity bill. A few minutes spent finding those figures gives you a more useful answer than a general claim that all desk lamps are cheap.
If your concern is the whole electricity bill, keep the scale in view. At the same assumed rate, leaving that 8 W lamp on continuously costs $28.03 a year. Switching it off when you finish still saves energy, but changing one small lamp is unlikely to explain a large bill increase by itself.
All dollar amounts in this blog are AUD. Examples exclude fixed supply charges, purchase prices and replacement parts unless a section explicitly includes them.
How to calculate a lamp's electricity cost
Start with the power drawn while the lamp is on. Divide watts by 1,000 to convert to kilowatts, multiply by hours, then multiply by your electricity rate in dollars per kilowatt-hour. If your rate is written in cents, divide it by 100 first.
- An 8 W lamp is 0.008 kW.
- Four hours of use needs 0.032 kWh.
- At $0.40/kWh, that costs $0.0128, or 1.28 cents.
- Multiply by 365 for a yearly estimate: $4.672, rounded to $4.67.
A 30-day estimate uses 30 days, while the annual estimate uses 365. Multiplying the displayed monthly figure by 12 will not give exactly the same result because twelve 30-day months contain only 360 days. Rounding can create another small difference.
Desk lamp running-cost calculator
Estimate operating and standby costs using a constant power draw and a single usage rate. The comparison lamp is a hypothetical 60 W load on the same daily schedule, with no standby power. It is not a claim of equal brightness.
40c/kWh is an example. Enter your bill's usage rate. Off-state power applies only during the remaining hours of the day; enter zero if the lamp is disconnected or has no off-state draw.
Estimated cost per year
11.68 kWh per year
8 W on for 4 h, 0 W off for 20 h, one lamp.
Annual electricity cost
Six examples you can compare
A short reading session and an eight-hour workday create different totals even when the lamp is identical. The table separates those patterns so you can find the closest starting point. The wattages are illustrative inputs, not specifications for particular brands.
| Example | Power | Hours/day | kWh/year | AUD/year |
|---|---|---|---|---|
| Short reading session | 5 W | 2 | 3.65 | $1.46 |
| Evening desk use | 8 W | 4 | 11.68 | $4.67 |
| Long workday | 12 W | 8 | 35.04 | $14.02 |
| Higher-power comparison | 60 W | 4 | 87.60 | $35.04 |
| Lamp left on continuously | 8 W | 24 | 70.08 | $28.03 |
| Six evening desk lamps | 6 × 8 W | 4 | 70.08 | $28.03 |
Notice that six 8 W lamps used four hours daily cost the same as one used around the clock in this simplified model. The total number of lamp-hours matters. For a shared study, home business or several children's desks, count every lamp before estimating the household total.
A higher electricity rate changes the result in direct proportion. At 50c/kWh, the 8 W evening example costs $5.84 per year; at 30c/kWh, it costs $3.50. Neither rate is a prediction for your address. Both show why the usage charge on your own bill belongs in the calculation.
Which wattage should you enter?
Use operating input power for the whole lamp where it is available. A product may list several electrical figures, and they do different jobs. The LED light source rating, adapter capacity and actual power at the wall need not be identical.
A fitting's maximum is not its consumption
If a table-lamp fitting says "maximum 60 W" but contains an 8 W bulb, the marking is a limit for the fitting, not a statement that the lamp consumes 60 W. Start with the bulb's rated power, and account for any other powered features if they are present. Follow the fitting's instructions when selecting a replacement.
An adapter label describes capacity
An adapter marked 12 V, 2 A has a stated output capacity of 24 W. Multiplying those numbers does not establish that the connected desk lamp always uses 24 W. Look for the lamp's input-power specification, or measure the complete setup with an appropriate plug-in electricity meter.
USB charging can be a separate load
A lamp that charges a phone may power both lighting and charging electronics. A calculation based only on the light misses the charging load. When measuring it, repeat the test with the charging feature unused and with a device connected, then label each result so you know which routine it represents.
Keep units separate. Australia's Energy Rating guide describes watts as electrical power, lumens as light output and Kelvin as colour temperature. An "800 lumen" label or a "4,000 K" setting cannot be entered as watts.
Find the right electricity rate on your bill
Use the usage charge expressed in cents or dollars per kWh. Energy Made Easy's tariff guide explains the difference between single-rate and time-of-use tariffs. A single-rate estimate is straightforward. With time-of-use billing, separate the lamp's hours into the relevant price periods and calculate each portion.
For example, suppose the lamp runs for two hours at an assumed 50c/kWh and another two hours at 25c/kWh. At 8 W, the daily total is $0.008 + $0.004 = $0.012, or 1.2 cents. That works out to $4.38 over 365 identical days.
For those equal time periods, entering 37.5c/kWh in the calculator produces the same energy-cost total. It is an hours-weighted rate for this particular routine, not a simple average you should apply to an unrelated schedule.
Do not add the full daily supply charge to one lamp's consumption estimate. It is a separate fixed charge in the tariff, not a per-kWh price. If you use solar, free-use periods or a more complicated plan, this tool remains a simple usage-cost model; it does not calculate export credits, demand charges or the total bill.
Standby power can matter for a lightly used lamp
Some smart lamps remain powered so an app or remote can turn them on. The Australian Government's lighting advice recommends checking smart-light standby consumption before buying. A lamp that looks dark is not necessarily drawing zero power.
Here is a separate assumed example. If a lamp draws 0.5 W while off for 20 hours a day, it uses 3.65 kWh across a year. At 40c/kWh, that adds $1.46. Added to the 8 W, four-hour operating example, the total becomes $6.13 per year.
The calculator counts standby only during the hours the lamp is not operating. It does not add 24 hours of standby on top of four hours of use. Enter the measured or specified off-state draw, and enter zero if switching off at the power point fully disconnects the lamp.
A smart hub or shared charger is outside the tool's lamp-only boundary. If you want the cost of a complete lighting setup, measure those devices separately. Avoid assigning the same shared accessory's consumption to each lamp and accidentally counting it several times.
Does dimming cut the cost in half?
Do not assume that a 50% brightness setting means half the wall power. The relationship depends on the lamp and its electronics. Measure the setting you use, or calculate with the rated operating power and describe the result as a rated-power estimate.
You can also test two routines in the calculator: one using measured full-brightness power and one using measured reading-setting power. Change only the power input so the difference represents the setting, not a simultaneous change in hours or tariff.
Is a desk lamp cheaper than lighting the whole room?
It is cheaper when the total power you switch on is lower for the same period. Suppose four ceiling lights draw 10 W each and a desk lamp draws 8 W. At the example rate and four hours daily, the ceiling lights cost $23.36 a year, while the desk lamp costs $4.67.
That comparison answers a cost question, not a lighting-design question. A desk lamp illuminates a task area; ceiling lights cover a wider space. If you still need room lighting to move around or work comfortably, including both loads gives an honest estimate. Adding a lamp while leaving every ceiling light on does not save electricity.
The government's household lighting guide suggests using natural light where practical and choosing lamps or spotlights when whole-room lighting is unnecessary. Start with the lights you genuinely need, then compare their combined power.
For an evening routine, write down which lights remain on. You might use one ceiling light and one task lamp instead of four ceiling lights. The calculator can compare a combined wattage, but its lamp-count field assumes identical loads. For different fixtures, add their active watts first and use a count of one.
Will a more efficient lamp pay for itself?
A replacement can make financial sense when it reduces a substantial existing load. A small efficiency improvement between two low-power lamps may save very little money. Compare purchase cost with the calculated electricity saving before paying extra for an efficiency claim.
Replacing a higher-power light
Assume a 60 W light is replaced by an 8 W light that provides acceptable illumination for the same job. Four hours daily at 40c/kWh saves about $30.37 a year. If the replacement costs an assumed $20, the simple electricity-only payback is about 7.9 months.
This is a worked scenario, not a promise about any product. It excludes installation, replacement parts and changes in usage. The Energy Rating comparison guide uses lumens to help match old bulbs with LED replacements. Check light output and beam distribution as well as power.
Replacing an LED with a slightly lower-power LED
Moving from 8 W to 6 W saves about $1.17 a year on the same schedule. An extra $80 spent purely to achieve that saving would take about 68.5 years to recover in this simplified calculation. Spending more could still buy an adjustable arm, better controls or a replaceable light source, but the electricity saving alone is small.
There is also an environmental question beyond the bill. A Pacific Northwest National Laboratory research report summarises earlier life-cycle studies in which electricity during operation dominated the lamps' environmental impacts. Those studies concern specific lamp technologies and assumptions; they do not prove that discarding every working LED lamp is beneficial.
For a functioning low-power lamp, calculate the actual saving before replacing the whole unit. Keeping a suitable fitting and changing a compatible bulb may be a different decision from buying a new integrated lamp.
Choose a useful lamp, then compare its cost
A lamp that needs to sit at an awkward angle or cannot light your work area properly is a poor purchase even if its wattage is low. Check reach, head adjustment, base footprint and controls. Ask whether you can aim the light without putting the bright source in your normal line of sight.
Replaceable bulb
Check the socket type, bulb dimensions and fitting instructions. A compatible LED bulb may let you keep a lamp you already like. Access to the bulb matters if the shade or housing is difficult to remove.
Integrated LED
Check warranty and repair options for the complete lamp. A long claimed LED life does not tell you whether its adapter, controls or arm will remain serviceable, or whether the light module can be replaced.
ENERGY STAR's technical explanation notes that LED light output can gradually decline over time and that thermal management affects useful life. A rated lifetime is therefore not a guarantee that the entire lamp will work without problems for that many hours.
For a new lamp, compare energy use at a setting that meets your needs. The lowest-watt product is not automatically the right one. Product photos cannot establish its wall power, and a generated lifestyle image is not a product test.
If you are considering an adjustable desk lamp, the BenQ listing is one place to inspect the current model's controls and power information. No measured wattage, price or availability is assumed in this blog.
View BenQ listing on Amazon AUAs an Amazon Associate, LampScout earns from qualifying purchases.
Measure your real routine without guessing
A suitable plug-in electricity meter can record the energy used by the lamp and its adapter together. Check the meter's instructions and low-power measurement capability before relying on tiny standby readings. Keep all equipment within its rated limits and use it as directed.
- Connect only the lamp and its normal adapter through the meter. Leave unrelated devices off that measurement channel.
- Run it at the brightness you normally use. Record the setting and whether any charging feature is active.
- Read the accumulated kWh over a known interval. Divide by the hours measured to find average kW, then multiply by 1,000 for average watts.
- Measure the off state separately if the lamp stays connected between sessions. Do not confuse that figure with operating power.
- Repeat if the first reading is too small for the meter to resolve reliably. A longer interval can give a more useful energy total.
Suppose your meter records 0.048 kWh over six operating hours. That is an average of 0.008 kW, or 8 W. Enter 8 in the calculator and use the hours from your normal daily routine, not necessarily the six-hour test period.
With a rechargeable lamp, cordless use moves the measurement to charging time. Measure energy drawn through the charger over a complete charging cycle, then multiply by the number of cycles. A hypothetical 0.020 kWh charge costs 0.8 cents at 40c/kWh. Thirty such charges cost $0.24, before any charger standby use.
Do not calculate a rechargeable lamp's grid cost from battery capacity in mAh alone. Charging losses, battery voltage and the lamp's consumption complicate that route. Measuring charger energy avoids treating a battery rating as if it were a wall-power reading.
Common questions
Do LED desk lamps use a lot of electricity?
A low-power lamp can have a small operating cost, but calculate it from the actual watts and hours. In this blog's example, 8 W for four hours daily costs $4.67 a year at 40c/kWh. That figure does not describe every LED desk lamp.
How much does a desk lamp cost per hour?
An 8 W lamp costs 0.32 cents per hour at an assumed 40c/kWh. A 60 W load costs 2.4 cents per hour at that same rate. Multiply the hourly cost by the hours you use it, and add standby separately if applicable.
Is it expensive to leave a lamp on all night?
The cost depends on its power. An 8 W lamp left on for eight hours costs 2.56 cents per night at 40c/kWh, or $9.34 across 365 nights. That is a calculated energy cost, not a recommendation to leave a lamp running unattended.
Does a 60 W maximum label mean my lamp uses 60 W?
No. A fitting's maximum marking is not its actual operating consumption. Check the bulb or complete lamp's power rating. An adapter's maximum output capacity also does not establish what the lamp draws during normal use.
Are watts and lumens the same thing?
No. Watts describe electrical power, while lumens describe light output. Use watts to estimate consumption and lumens when comparing output. The Australian Energy Rating tables explain how to compare older bulb technologies with LED replacements.
Are rechargeable lamps free to run?
No. They use energy when charged. To estimate the electricity cost, measure the charger's kWh for a complete cycle and multiply by your usage rate and number of charges. Cordless operation changes when the lamp draws from the mains.
Does switching to warm light lower the bill?
A warm-colour setting alone does not establish a lower power draw. Compare the lamp's specified or measured consumption at the settings you use. Do not put its Kelvin number into an electricity-cost calculation.
Why does the calculator not include my supply charge?
It estimates the lamp's usage cost. The fixed supply charge is a separate part of an electricity tariff, so assigning all of it to the lamp would answer a different question. The tool also excludes demand charges, solar export effects and accessory loads that you have not entered.
What should I change first to reduce lamp running costs?
Check your hours of use, actual power and off-state draw. Switch off unnecessary lighting, then calculate whether a replacement would save enough to justify its cost. For a working 8 W lamp, buying a slightly lower-power model may save less than changing an inefficient bulb elsewhere.
Sources and calculation notes
- Australian Government: household lighting. Practical efficiency advice and smart-light standby considerations.
- Energy Rating: choosing the right lamp. Definitions of power, light output and colour temperature.
- Energy Rating: comparing lumens to watts. Output-based comparisons when replacing older bulbs.
- Energy Made Easy: electricity tariffs. Usage rates and tariff structures.
- ENERGY STAR: learn about LED lighting. LED depreciation and thermal management.
- PNNL: life-cycle assessment of LED lighting products, part 3. Research context, published in 2013; not a current model comparison or Australian cost survey.
All examples and chart values are calculated from the stated inputs. Annual totals use 365 days; monthly totals use 30 days. Figures assume steady input power and an unchanged tariff, with money rounded only for display. No lamps were physically tested for this blog. The hero is an AI-generated illustration of a generic desk lamp, not a product photograph.